Community > Non-Thorn Related

Slime

(1/2) > >>

in4:
I was reading about this product. Apparently you can buy inner tubes with it already in. You can also add your own slime as you think appropriate.
I also read that the slime can coagulate around a valve and potentially ruin and make removing it difficult.
Some suggest that it’s a solution looking for a problem and that if you run quality tyres with quality tubes it is unnecessary.

The sole flat I had over my recent 1500km Spain-Portugal tour was down to a faulty tube that seemed to split at a seam. ( forget the brand but it wasn’t a Schwalbe)? Of course this was inconvenient, particularly when it’s a rear tube and I was fully loaded with panniers etc. My Schwalbe Dureme tyres were very good indeed btw.

Has anyone used slime and has an experience to share?

mickeg:
I did a trip where there were a lot of thorns (the pointed type, not the wheeled type), fitted a suspension front fork to my Nomad Mk II and pretended it was a mountain bike.  We were doing day trips, not touring.

Lots of thorns in the area.  I had a tube failure, but it was a tube defect.  Otherwise no problems.  But, can't say if I would have had any problems if I did not use slime in my tubes first.

Slime is water based, you can use water to clean it off, which is one reason I chose that, I could add it through a presta valve with a removable core, and then clean out the valve seat, and replace the core.

Later, adding air, I was careful to avoid having air in the tube come out when I took the pump chuck off the valve, as I did not want sealant blowback.

That is the only time I used it.  I still have a bottle of it and if I was to go there again, I might use it again.

I have heard that if you have sealant on a tube, that putting a patch on the tube can be problematic.  Have heard that in a generic way, I do not know if that includes Slime or not, as I would assume if you had a tube that you washed off the sealant, dried it, that a patch would stick.  Have not tried it, but it is something to be aware of.  I would be inclined to use a bit of rubbing alcohol to wipe off the area to be patched and let that dry first.

Regarding sealant, there are several different sealants that people use for tubeless tires, but the only sealant I have bought is Slime.  Slime sealant for tubes is different than their sealant for tubeless tires, I do not know what the difference is.

JohnR:
I would note that the various sealants (mainly Doc Blue or Stans (which may be the same)) I have used with tubeless tyres are water-soluble unless dried out. If I am changing tyres then first I suck out as much sealant as I can with a big syringe and then wash off the rest of the sealant to leave the tyres clean ready for reuse. When I'm inflating a tyre that contains sealant I position the valve to be around 45 degrees from the bottom so any sealant in the valve area will drain into the tyre.

steve216c:
Before I switched to Marathon Plus tyres I purchased ‚self repairing‘ tubes with slime type liquid.

The slime adds rolling resistance and the valves can be a weak point. My wife’s and my bikes had occasional unexplainable flats/slow puncture ( or so I thought) which was actually slime that had stopped the valve closing properly. I purchased a valve remover for the car style valves I prefer and would remove and clean when needed.

If you get a flat, you need to ride for it to seal. So removing elements that had pierced the tyre (glass or thorns) means tube needs a patch to seal it or you need to pump and ride immediately to seal the tube.

Although I did find a couple of unexpected slime repaired tubes over the 3-4 years I tried these, I found they were only useful in limited flat situations.

Since switching to Marathon Plus tyres and regular tubes I’ve been almost puncture free for several years. I’d personally not bother with slime or similar again.

rafiki:
I added Muc-Off tube sealant to my MTBrompton 20" Big Ben tubes. Each time I wanted to check tyre pressures I couldn't because the valves were solid with the stuff. I had to remove the valves and wash them before reinflating the tyres. I had been very careful to add the correct volume of sealant by using a large syringe to measure the exact recommended quantity. I recently discarded the tubes and started again with new tubes and new Big Ben Plus tyres. Muc-Off sealant - never again.

Navigation

[0] Message Index

[#] Next page