Author Topic: Chain Decision  (Read 3245 times)

Thomas777

  • Full Member
  • ***
  • Posts: 106
Chain Decision
« on: February 09, 2017, 03:52:42 pm »
I thought I sorted this out before but cannot seem to find the info.
What speed chain should I consider for my new set up?
Thanks!

bobs

  • Hero Member
  • *****
  • Posts: 601
Re: Chain Decision
« Reply #1 on: February 09, 2017, 04:01:26 pm »
If it is a rohloff hub a single speed chain for an IGH should do .

Bob
« Last Edit: February 09, 2017, 10:49:05 pm by bobs »

RonS

  • Full Member
  • ***
  • Posts: 132
Re: Chain Decision
« Reply #2 on: February 09, 2017, 06:43:35 pm »
Like bobs said.

Any 8 speed 1/2 X 3/32 chain is also acceptable.

https://www.rohloff.de/en/service/faqs/index.html#c9537

REI will have a good selection of SRAM or KMC chains.

Matt2matt2002

  • Hero Member
  • *****
  • Posts: 1893
Re: Chain Decision
« Reply #3 on: February 09, 2017, 10:25:50 pm »
I have just fitted a KMCX1 to my Raven.
The previous one did 6,000+ miles.
Turned once. Chainglider on all the time.
I used Wiggle £23.38

I also bought a KMCX1 Ept. Extra protection apparently.
£31.45.
I'll keep that one for next time.

I made the mistake of cutting it too short so think and measure carefully or you'll have to add a link.
Never drink and drive. You may hit a bump  and spill your drink

John Saxby

  • Hero Member
  • *****
  • Posts: 2000
Re: Chain Decision
« Reply #4 on: February 10, 2017, 06:48:28 am »
I've used the KMC 8.93, Tom. They are inexpensive (about $15 in Canada) and seem to work just fine. There are two grades -- the nickel is slightly more expensive, and you need to ensure that the Quick-links match the chain. (The nickel is shiny/shiny.)

SRAM make a range of 8-spd chains.  I have an 850 at home, and will probably fit that in the spring.

Cheers

Thomas777

  • Full Member
  • ***
  • Posts: 106
Re: Chain Decision
« Reply #5 on: February 12, 2017, 11:07:32 pm »
So as I continue my education on Rohloffs another question comes to mind. Do you get more mileage while using a IGH vs. Derailleur?

Danneaux

  • Administrator
  • Hero Member
  • *****
  • Posts: 8229
  • reisen statt rasen
Re: Chain Decision
« Reply #6 on: February 12, 2017, 11:35:25 pm »
Quote
Do you get more mileage while using a IGH vs. Derailleur?
Yes! Surely! The primary reasons are twofold:

1) The chain does not have to bend sideways to accommodate a range of gears. This is true at both ends -- single chainring, single sprocket/cog. The chain incurs less wear by running in a straight line.

2) There are (for Rohloff installations using eccentric bottom brackets or sliding or ramped dropouts) no small tension pulleys for the chain to wrap around. This removes a major wear and friction point. Of course, for Rohloff installations using a derailleur-like chain tensioner, there is no difference in this regard.

Because the chain just runs in a straight line without lateral flexing, it does wear much longer than in a derailleur application. Also because the chain does not need to move laterally, it is possible to fit a "floating" chain case (i.e. Hebie Chainglider) to fully enclose the chain and protect it from grit and water exposure and lubrication loss. Of course, this will only work with some chainring/sprocket combinations because Hebie only makes the Chainglider to fit specific applications.

Best,

Dan.

Thomas777

  • Full Member
  • ***
  • Posts: 106
Re: Chain Decision
« Reply #7 on: February 13, 2017, 10:29:24 pm »
Thanks for your help! Just built the front wheel for my wife's touring bike yesterday. Her bike is going to get 1 more coat of clearcoat then the build can proceed.